RICE BELT HEADER

Request a Quote Find a Dealer

Rugged, ground-hugging header for rice

Few crops are as difficult to harvest as rice. It is tough, abrasive, and yields run high. In addition, you’re often harvesting in extremely wet ground conditions. These challenges lead to tough combining with conventional equipment.

The Honey Bee Rice Belt header speeds up harvest with features that allow it to hug the ground for faster, easier harvesting, eliminating the twisting and tangling problems associated with conventional auger headers. Using a proven draper-and-auger feeding system, the Honey Bee Rice Belt Header uniformly feeds the crop heads first, providing consistent harvest speeds, superior threshing and better harvest efficiency.

Features

Knife Drive

The knife is driven by a 3 5/16″ (8.4 cm) stroke, epicyclic knife drive which ranges from 1,284–1,400 strokes per minute (depending on make of combine), eliminating fore/aft movement. The knife drive is driven by a low maintenance hydraulic drive motor. Optional double knife drive systems are available.

Double Reel Drive

The hydraulically driven reel is easily controlled using standard in-cab controls allowing for quick reel adjustment in changing crop conditions.

Deck and Feed Auger

Fasten your seat belt. The 68″ (172.7 cm) centre deck combined with the 72″ (182.9 cm) feed auger with retractable fingers smoothly feeds the crop into the feeder housing without twisting or tangling. A hinged door under the centre deck allows easy cleaning of foreign material like rocks and roots that might jam the feeder.

Lateral Leaf Spring Float System

The header has excellent floatation and ground-hugging capability. Lateral and vertical leaf spring suspension allows the header to float independently of the combine’s OEM accumulator floatation system. You’ll put more crop through the combine, leave less in the field, and reduce rock damage to your cutting system.

See more

UHMW Skid plates

UHMW skid plates are standard on all models to protect the cutterbar when cutting crops close to the ground.

Draper Speed Control

Draper speeds are hydraulically controlled and adjustable. Hydraulic power is split 50% to the side drapers and 50% to the centre deck. Independent control over the drapers gives you the power to move heavy material smoothly and efficiently.

Polyester Drapers

Drapers are made of long-lasting, rubberized polyester with fibreglass-reinforced slats and tie bar connectors. The drapers are standard 42″ (106.7cm ) width.

Draper Drive

The 2 1/2″ (6.4 cm) diameter drive rollers provide traction in heavy crop conditions. Powered from the outside by a hydraulic motor, the drapers move the crop towards the centre deck and feed auger for more uniform feeding.

Draper Tension and Tracking

The canvas can be adjusted for tracking and tightening, which allows even tension on both the front and rear of the rollers. A quick release lever allows for ease of canvas and roller cleaning.

Feed Auger Slip Clutch

A slip clutch on the feed auger disengages to prevent damage caused by foreign material running through the combine.

Independant Hydraulic System

A PTO driveline powers a hydraulic pump that is mounted to a step-up gear box that drives the feed auger. The step-up gear box is lubricated with oil supplied from the header hydraulics, which is double filtered to keep the system clean.

Manual Header Tilt

No-wrench tilt adjustment allows you to set the platform at the best angle to perform in all crops — short, tall, bulky or sparse.

SCH Cutting System

The SCH Easy Cut Cutting System provides smooth, superior cutting. Spring steel guards, with cutting edges on top and bottom, along with alternating, bolted, heat-treated sections, eliminate the need for hold downs. The system keeps dirt and debris from accumulating under the knives for increased performance in severe cutting conditions.

Options

Cross Auger

Hydraulic drive cross augers assist in material flow from the drapers to the feed auger. The auger is adjustable to match varying crop conditions and increases combine capacity in bulky crops like peas and mustard. 20′ augers are available on all headers and 30′ augers are available on headers 36′ and longer.

Fore/Aft Reel Adjustment

A hydraulic adjustment with in-cab control is available for fore/aft positioning for on-the-go response to changing crop conditions with a 16″ operating range.

Jack Adjustable Castoring Gauge Wheels

Castoring gauge wheels have rubber spring suspension and are vertically adjustable. They are available as optional equipment and recommended on headers 25′ and wider. The castoring design eliminates gouging when turning.

Hay Guard

No-wrench tilt adjustment allows you to set the platform at the best angle to perform in all crops — short, tall, bulky or sparse.

Levee Shield

A levee shield protects the rollers when cutting up against levees, reducing harvest misses.

Stainless Steel Throat

Stainless steel is harder, reduces friction and outlasts carbon steel. The stainless steel throat gives your header better feeding ability and reduces wear caused by extremely abrasive crops like rice.

Specs

SpecificationsSPR21SPR25SPR30SPR36
Width21′ (6.4 m) 25′ (7.6 m) 30′ (9.1 m) 36′ (10.9 m)
Weight* (no reels or options included)5,269 lbs (2,390 kg)5,911 lbs (2,681 kg)6,786 lbs (3,078 kg)7,200 lbs (3,266 kg)
Hydraulic SystemSelf contained hydraulic system on the header. Single gear pump with step up gear box driven off of bottom feeder house.
Header Floatation Leaf spring float system standard on all models.
Cutting System SCH Easy Cut, spring steel guards, bolted sections, roller spacer bar.
Knife Drive SCH 3 5/16″ (8.4cm) stroke, hydraulically driven, approximately 1,100 – 1,300 strokes per minute.
Knife Drive Standard single drive with option of double drive knife.
Draper 42″ (106.7 cm) wide rubberized polyester, fibreglass reinforced rubber slats. Hydraulically driven.
Centre Deck Hydraulically driven, 68″ (172.7 cm) wide centre canvas. Speed adjustable on header.
Feed Auger Mechanically driven, 18″ x 72″ (45.7 cm x 182.9 cm) retractable finger auger.
Reel(s) 21′25′ 30′ 36′
Reel(s) Pickup Reel – Universal UII, (Series 2) 6 bat, 42″ (106.7 cm) diameter, plastic teeth only.
Reel(s) Pickup Reel – HCC Polytine Level II series, 6 bat, 42″ (106.7cm) diameter.
Reel Drive Standard – using combine hydraulic system. Header driven reel optional. Reel speed adjustable in cab.
Gauge Wheels Optional
Storage Transport Optional
Formed Fit Poly Skid (UHMW) Standard
Combine Adapters Available for most models of self-propelled combines.
Fore/Aft Standard
Automatic Header Height Control Optional

Contact your local territory representative

Phone: (306) 296-2297
Email:

"*" indicates required fields

Hidden